5 Gallon Air Tank 150DB super loud 240 PSI Air Pressure Gauge For Train Horn Car

  
This On-board system is designed to use it with any high-pressure air horn that require an on-board air system. Comes with a 5 Gallon (18 liter) air tank, 200 PSI heavy duty black color compressor, air pressure gauge, pressure switch, hose and mounting hardware. This is truly a great quality product you can count on. Ideal for Cars, SUV, Truck, RV, Marine and more. Power:12 Volts Maximum Pressure:200 PSI Duty Cycle (100 PSI):100% Maximum Current Draw:23Amp Flow Rate (0 PSI):1.7 CFM Maintenance Free:Yes Length:10-¾" Width:4" Height:6-¾.

5 Gallon Air Tank 150DB super loud 240 PSI Air Pressure Gauge For Train Horn Car. Tank Capacity:5 Gallon(18L) Color:Black Air Pressure Gauge Included:Yes Maximum Pressure:250 PSI Working Pressure:200 PSI Total Ports:8 Front Ports:1 x ¼", 1 x ½" Bottom Ports:1 x ¼" Left Side Ports:1 x ¼" Right Side Ports:3 x ¼", 1 x ½". 1 200 PSI 12V Air Compressor. 1 5 Gallon Air Tank.

Make sure you never attempt to disassemble this horn kit's electrical components. Never use your bare hands to any part of the compressor immediately after or during use. Avoid operating this product in an area with risk of falling or submergence into a liquid (water).

Do not reach out for or touch any component that has fallen or been submerged into water. Make sure you set up in areas with good ventilation.

Never sound the air horn anywhere near your ear(s) or that of another person. Make sure your battery ground is detached before getting your installation started. Employ equipment for eye protection during drilling operations. The specific voltage requirement for this horn kit is 12 volt DC, therefore installation must be done to a DC power source of 12 volts. Identify a suitable area for mounting, preferably an unobstructed sheet-metal surface like the frame or body of.

The vehicle so as to provide a firm platform which will help protect the horn from damage due to excessive shaking. Do not attach the horn to any plastic or other flexible material.

Using the bracket as a guide estimate and mark the positions for the holes and then perforate to size using a drill. Use the provided mounting hardware to fasten the horn. The ideal location for the compressor to be installed is a dry area inside your engine compartment where it will be safe from exhaust and engine manifold heat. To make the compressor firm and secure, drill a hole of 3/16.

IMPORTANT: The compressor must be mounted vertically (with air exhaust port facing downward). Install the bolt's head into the compressor housing's slot. Tighten the compressor firmly to the vehicle with the provided lock washer and nut.

Connect one side of the airline to the compressor's air exhaust port and the other side to the trumpet's barbed fitting. Do not make any sharp bends or kinks in the tubing which could alter the sound of the horn or even restrict airflow. IMPORTANT: Airlines are sometimes already pre-installed. In such situation, ensure that they are inserted entirely into the fittings on the trumpet and compressor. ELECTRICAL CONNECTIONS (FACTORY HORN SWITCH).

For vehicles with a two-terminal factory horn, transfer the wires to the compressor's terminals. If the horn doesn't sound even if the compressor motor turns on, simply reverse the wires. For vehicles with one-terminal factory horns, make sure you transfer the wire to the compressor's positive (+) terminal. The negative (-) terminal uses a 16-gauge wire or heavier to connect to ground.

ELECTRICAL CONNECTIONS (NEW HORN BUTTON). In a dry location, install the relay provided making sure that terminals face downwards near the horn.

Using a 16-gauge wire or heavier, connect PIN 87 of the relay to the positive (+) terminal of the compressor. Connect PIN 85 of the relay to the horn button (not provided). The other horn button terminal is attached to any rust and paint free metal to ground. Connect using an 18-gauge wire or heavier.

Connect PIN 30 and 86 of the relay to the battery, alternator or other positive (+) of 12-volts. Make sure the wire used is a 16-gauge wire or heavier. Use a 20A fuse (not provided) to protect the electrical circuit. Always keep the appearance of the horn clean and all wiring reliable.

Regularly check and tighten the fixing screws of horn and bracket to ensure reliable grounding. The fixing method of trumpet has great influence on its pronunciation. In order to make the sound of the horn normal, the horn can not be rigidly installed, so it is fixed on the buffer bracket, that is, between the horn and the fixed bracket, a leaf spring or rubber pad should be installed. Check the output voltage of generator regularly. If the voltage is too high, the horn contact will be burned.

If the voltage is too low (lower than the rated voltage of the horn), the horn will make abnormal sound. When washing the car, it is not allowed to wash the trumpet directly with water, so as to prevent the water from entering the trumpet and the trumpet from sounding.

When repairing the horn, pay attention to the position of each metal pad and insulation pad, and do not install them wrong. The continuous pronunciation of the horn shall not exceed 10s to avoid damaging the horn. Do not put all kinds of foreign matters into the horn to avoid abnormal sound. Air Tank and 200 PSI Compressor. Check the compatible chart &.

Item specifics & Picture & Description. Before placing order, to make sure you will get the right part that fits your vehicle.

We accept and offer free. Find a better price from other store. Or we don't provide. Free return for reasons listed above, and. Will be subject for the reasons above. We will always do our best to get your satisfaction. Struts & Suspension Kit & Hubs.

2 Rear Wheel Hub Bearings For Dodge Jeep Caliber 07-08 Compass Patriot 07-17 4WD.